Attempting to understand the UFO politics circuit
I have been looking at this circuit for some time and did make an attempt to replicate using basic components. If the circuit works as stated then maybe it needs for me to apply myself and go back to it, there are a couple of issues. I have also been studying the Stan Meyers Waterfuelcell and the similarities between the UFO Politics circuit are startling. In the SMW the 316 L pipes inner and outer are tuned to the same frequency in an audio range if there are more than one set of pipes which there usually are they must all be tuned the same inner & outer in an audio frequency. The coil must be in resonance with the tuned pipes, in the case shown the alternator is tuned to three different phases as it’s presumably installed in a car. This is basically a coil and capacitor in resonance together, but where is the capacitor in the SMW cell you might ask? Well its right in front of you, it’s the 316 Stainless steel pipes and the water that will be surrounding them but particularly between the pipes, in a capacitor there is a dielectric, in the SMF cell the water is the dielectric the inner of the outer pipe and outer of the inner pipes is essentially where the action happens. If the SMW cell is built correctly it will not produce much gas to start, it must go through a conditioning phase which can take some weeks, as this conditioning is taking place a white film builds up on the area between the two pipes either on the anode or cathode, when this occurs gas production improves greatly and eventually gets to where it has full gas production. How is this similar to the UFO Politics circuit? Well in the UFO circuit there is a coil and an electrolytic capacitor, when both these are in resonance the circuit is in resonance however just as with the SMF cell there is little radiant energy produced as the circuit – electrolytic capacitor and battery must become conditioned. This can take time, so if I’m right why does P Kelly feature the UFO circuit without the electrolytic cap in several pages? He also states that the electrolytic cap turns cold electricity into hot! Consider Howard Hayley’s comment – on page after circuit Chap 6 page 41

Stan Meyer’s Water Fuel Cell
Howerd Halay of the UK stresses the major difference between “conditioned” batteries and all batteries which have not been conditioned. He says: to condition a battery or capacitor, it needs to be repeatedly charged with ‘cold’ electricity and discharged again. Cold electricity is either high-frequency AC electricity or alternatively DC at high voltage. With cold electricity, the electricity flows outside the wires (Steinmetz) and so, Current does not equal Voltage divided by Resistance as Ohm’s Law suggests. Instead, Current equals Voltage x Resistance x a Constant “C” which has to be determined by experimentation. It is also possible to get cold electricity from pulsed DC, provided that the DC voltage is over 80 volts. If using that technique, then the sharper and faster the pulses, the better.
When you first pulse an AC or DC capacitor, it behaves normally. After approximately 12 hours of continuous pulsing a change occurs in the behaviour of the capacitor. In the case of the water capacitor, it develops a nano coating on one side only. When measured with a resistance meter it shows no resistance at all. One can say that one side becomes quasi superconducting. In the case of an ordinary capacitor, there is no reason to believe that it behaves differently. The capacitor also charges much faster than before and when the power source is switched off it continues charging! Yes you read that correctly. In my case it fires pulses for up to 3 minutes after the power is switched off, which is why they are dangerous. The firing decays exponentially although I haven't yet tabulated it scientifically – I’ll leave that to other people to do’.

How is the resonance measured in the UFO circuit? Is it done by using a neon light with its legs in the positive and negative of the circuit going to the load? When in resonance the light turns from orange to pink? What capacitance should the electrolytic capacitor be? What voltage? The type of coil used whether single wire or four wires looped in parallel will decide the type of capacitor
This resonance could be measured with an oscilloscope also?
P Kelly also states that the following:
The main requirement is high-speed operation, voltage rating of at least 400V and current rating of at least 5 amps.
This relates to the first diodes NTE 576 or equivalent I’m using if I’m reading this correctly
The circuit calls for 36 volts incoming voltage using three 12 volt batteries in series, car batteries are possibly too much amperage for this, it’s possible to get lower amperage batteries. The circuit apparently cannot handle a voltage of 36 volts! P Kelly recommends only 7 volts! The coil should be no more than 1.5 Ohms . The wire can only carry 4.6 amps.
So by reducing the duty cycle that will help alleviate that problem?
P Kelly:
‘The magnetic field produced by a single strand is generally less than the magnetic field produced by two strands
carrying the same total current. So, if we were to pick 22 swg wire, then we could measure out four 133.5 metre
lengths, join them at the start, and wind the four strands simultaneously, side-by-side to form a coil with a DC
resistance of 1.45 ohms. It is important that the strands are exactly the same length so that they carry exactly the
same current and no one strand gets overloaded with current due to it having a lower resistance than the other
strands. It should be realised that as the maximum current which the wire can carry is 4.8 amps and the
resistance is only 1.45 ohms, the maximum continuous DC voltage which can be sustained by the coil is only 7
volts, and so as a 36-volt battery is being used, we must adjust the frequency and duty cycle very carefully,
especially since we are starting at very low frequencies. If the full battery voltage is applied continuously to the
coil, then the coil will be destroyed’.

In my case, I used a AC/DC variable voltage and amperage supply of 0 to 30 volts and 0 to 1.5 amps doing replication of circuit. The one I just got is 0 to 30 volts and 0 to 5 amps with digital display
It is probably better to build this circuit as laid out including the 555 timer chip
In conventional electricity electrons flow from negative to positive ie from the negative pole to the positive, but conventional electricity schematics show electricity flow from positive to negative as that is way they thought electricity flowed until modern times but of course they left the schematics as if electricity flowed from positive to negative, this has caused me quite a bit of confusion. In the case of radiant energy / cold electricity it is theorised that it flows the opposite way of conventional belief system ie backwards along the wires and so the in the case of cold electricity in the same direction as the arrow on the diode?

Views: 29

Reply to This

Replies to This Discussion


UFO Politics circuit (no capacitors) Chap 3 page 138

Reply to Discussion


© 2017   Created by Kev.   Powered by

Badges  |  Report an Issue  |  Terms of Service